Yard & Concrete · Calculator
Lawn Lime Calculator
Enter the lime your soil test recommends, the calcium carbonate equivalent printed on the bag and the size of your lawn. The calculator works out how much of that product to spread, how many bags to buy and whether to split it into two or more applications.
Lime to apply
468.8 lb
- Product per 1,000 sq ft
- 93.8 lb
- For your lawn
- 468.8 lb, 12 bags of 40 lb
- Applications
- 2, of 46.9 lb per 1,000 sq ft (234.4 lb each time)
Ohio State sets 50 lb per 1,000 sq ft as the most ground limestone to apply at one time, so the total is split in two, one application in spring and one in fall.
Penn State allows up to 100 lb of limestone per 1,000 sq ft at once on an established lawn, which would mean a single application.
Water the lawn after liming to wash the lime off the leaves, and do not apply it to wilted or frosted turf.
Ohio State University Extension HYG-4026; Penn State Extension, Liming Turfgrass Areas.
Lime recommendations usually assume pure calcium carbonate, so a weaker product takes more. A soil test calling for 75 pounds per 1,000 square feet means 93.8 pounds of a product with a CCE of 80 percent, or 468.8 pounds for a 5,000 square foot lawn.
Start from a soil test
Only a soil test from a state or commercial laboratory says whether a lawn needs lime and how much. Home kits and pH probes can show that the soil is acidic, but they do not work out the amount, which varies a lot from one soil to another. The laboratory reports it as the lime requirement. For Ohio lawns, Ohio State Extension puts the ideal pH between 6.0 and 7.0.
Adjusting for the product
Most soil test reports give the lime requirement in pounds of pure calcium carbonate, which has a calcium carbonate equivalent, or CCE, of 100 percent. The product you buy is usually weaker, and its CCE is printed on the bag; Pennsylvania requires it on every liming material sold there. To find how much product to spread:
product = recommendation × 100 ÷ CCE of the product
Penn State's example: a test calling for 75 pounds per 1,000 square feet, with a limestone of 80 percent CCE, means about 94 pounds of that limestone. If your report assumes another material, enter its CCE in the calculator instead of 100.
A worked example
A soil test recommends 75 pounds of calcium carbonate per 1,000 square feet, and the ground limestone at the store has a CCE of 80 percent. That is 75 × 100 ÷ 80 = 93.8 pounds of product per 1,000 square feet, or 468.8 pounds for a 5,000 square foot lawn: 12 bags of 40 pounds. It is more than the 50 pounds Ohio State suggests at one time, so it goes on in 2 applications of 46.9 pounds per 1,000 square feet, one in spring and one in fall.
How much at one time
Lime goes on in limited amounts. Ohio State's table sets the most to spread at one time, in pounds of product per 1,000 square feet: 50 for ground, dolomitic or pelletized limestone, 20 for hydrated lime and 10 for burned lime. When the total is more, split it between applications in spring and fall. Penn State allows more limestone on an established lawn, up to 100 pounds per 1,000 square feet at once.
The calculator uses Ohio State's figures, the more cautious for limestone, divides the total into equal applications no larger than that, and says when Penn State's limit would mean fewer. On a new lawn, Penn State says the whole amount can go on at once if it is worked into the top four to six inches of soil before seeding.
Choosing a material
| Material | CCE | Most at once |
|---|---|---|
| Ground limestone | 70–95 | 50 |
| Dolomitic limestone | 70–95 | 50 |
| Pelletized limestone | 70–95 | 50 |
| Hydrated lime | 140 | 20 |
| Burned lime | 180 | 10 |
The figures are Ohio State's; the CCE of a real product depends on its purity, so use the one on the bag. Pelletized limestone is easier to spread and works faster than ground limestone, but costs more. Dolomitic limestone also adds magnesium, and Penn State recommends it where the soil test shows magnesium is low. Hydrated and burned lime act fast but are hazardous and hard to apply. Gypsum is not a liming material: it changes soil pH very little, if at all.
When to spread it
Lime can go on at any time of year, but not on turf that is wilted or covered in frost. Ohio State suggests spring or fall, when rain helps carry it into the soil, and watering the lawn afterwards to wash it off the leaves; aerating the lawn first helps it work in. The pH changes slowly: expect several months before it shows.
Questions people ask
How much lime per 1,000 square feet does a lawn need?
Only a soil test can say: the amount depends on the soil. Whatever the total, Ohio State suggests spreading no more than 50 pounds of limestone per 1,000 square feet at one time.
Can you put down too much lime?
Yes. Above a pH of about 8.0, nitrogen, phosphorus, iron and other nutrients become less available and the lawn thins out, which is why Ohio State advises against liming without a soil test.
How do I convert pounds per acre to pounds per 1,000 square feet?
An acre is 43,560 square feet, so divide the pounds per acre by 43.56. Choose “acre” in the calculator and it does this for you.
Sources
- Ohio State University Extension: Lime and the Home Lawn (HYG-4026, 2021) — lime requirement divided by CCE; Table 1, materials and maximum rate per application
- Penn State Extension: Liming Turfgrass Areas — CCE adjustment and example; 100 lb limit for established turf; new lawns