Sill & Rafter

Plumbing & Water · Calculator

Septic Tank Capacity Calculator

Enter the inside dimensions of the tank and its liquid depth, measured to the bottom of the outlet pipe. The calculator gives the liquid capacity in gallons and cubic feet and the gallons in each inch of depth, and, if you have the sludge and scum measurements, whether the tank is due for pumping.

From the inside floor of the tank to the bottom of the outlet pipe.

Optional, as measured by a septic professional.

Liquid capacity

1,077 gallons

Volume
248,832 cubic inches = 144 cubic feet
Gallons per inch of depth
19.9

Gallons are cubic inches divided by 231, the size of a US gallon.

For a septic tank, compare this with your state's minimum in the septic tank size calculator.

Geometry of the tank; US gallon from NIST SP 811, Appendix B.9; pumping threshold from EPA.

A tank's working capacity is the liquid it holds up to the outlet. A rectangular tank 96 by 48 inches inside, with 54 inches of liquid, holds 1,077 gallons.

What to measure

Take the dimensions inside the tank, not outside the walls. The depth that counts is the liquid depth: from the inside floor up to the bottom of the outlet pipe, the level the tank holds in use. Texas, for example, measures a septic tank's liquid volume from the bottom of the outlet. A tank with two compartments holds the same total; measure the whole length inside, and leave out the thickness of the baffle wall if you know it.

The arithmetic

  • Rectangular tank: length × width × liquid depth, in cubic inches.
  • Round tank standing up: the area of the circle, π × diameter × diameter ÷ 4, times the liquid depth.
  • Round tank lying on its side: the area of the part of the circle below the liquid line, times the length. The calculator works out that area for any depth.

A US gallon is 231 cubic inches, so the gallons are the cubic inches divided by 231. A cubic foot is 1,728 cubic inches, about 7.48 gallons.

A worked example

A concrete tank measures 96 inches long and 48 inches wide inside, and the liquid stands 54 inches deep at the outlet. That is 96 × 48 × 54 = 248,832 cubic inches, or 144 cubic feet. Divided by 231, it holds 1,077 gallons, and each inch of depth holds 19.9 gallons.

Gallons per inch

The calculator also shows how many gallons each inch of liquid adds at the current level. In a rectangular or standing round tank this figure is the same at every depth; in a round tank lying down it is largest at the middle and smallest near the top and bottom. It helps to read a level: if the liquid stands some inches below the outlet, multiply those inches by this figure for a rough idea of the gallons missing.

When to pump

EPA's guidance for homeowners says to pump the tank when the bottom of the scum layer is within 6 inches of the bottom of the outlet, when the top of the sludge layer is within 12 inches of the outlet, or when more than 25 percent of the liquid depth is sludge and scum. A septic professional measures those layers at the inspection; enter them in the calculator to see the share of the depth they take. EPA adds that household tanks are typically pumped every three to five years.

Is the tank big enough?

Once you know the capacity, compare it with the minimum your state sets for the house in the septic tank size calculator. The minimum depends on the bedrooms and, in some states, on the floor area or the appliances.

Questions people ask

How do I find the size of my septic tank?

Check first whether the capacity is in the permit record at your county or state office, or in the maker's drawing. If not, have the inside length, width or diameter and the liquid depth to the outlet measured, and enter them above.

How many gallons are in a cubic foot?

About 7.48. A cubic foot is 1,728 cubic inches and a US gallon is 231.

How much is pumped out of a septic tank?

Emptying the tank removes what it holds, so the liquid capacity this calculator gives is the size of a full pump-out of a tank at its normal level. EPA says household tanks are typically pumped every three to five years.

Sources