Plumbing & Water · Calculator
Pool Calcium Hardness Calculator
Enter the pool's volume, the calcium hardness you measured and the one you want. To raise it, add the strength of your calcium chloride from the label; to lower it, the hardness of your fill water. The calculator does the chemistry with published molar masses.
Calcium chloride to add
24 lb
- Raise by
- 100 ppm
- Product at 77%
- 24 lb (385 oz)
- Pure calcium chloride in it
- 18.51 lb
- This product per 10 ppm per 10,000 gal
- 1.2 lb
HTH's label says never more than 10 lb per 10,000 gallons at one time: for this pool that is 20 lb, so split the dose into 2 additions and test in between.
Follow your product's label for how to add it, with the pump running.
PubChem molar masses; NIST gallon; makers' labels.
Raising a 20,000 gallon pool from 150 to 250 ppm takes about 24 pounds of 77 percent calcium chloride flakes. Hardness only comes down by replacing part of the water with softer water.
What calcium hardness is
Hardness is the calcium and magnesium dissolved in water, and it is reported as milligrams per liter, or parts per million, as calcium carbonate. That is the unit of pool test kits, and the unit used here. The CDC's Model Aquatic Health Code explains both sides of it: too much calcium makes the water cloudy and leaves scale; too little, especially with low pH or low alkalinity, makes the water aggressive enough to dissolve plaster and attack metal parts, and it can stain the walls and floor.
Recommended ranges
| Source | Calcium hardness |
|---|---|
| CDC Model Aquatic Health Code (US public pools) | 200 to 400 ppm preferred; 100 to 200 ppm above 90 °F. For water balance, 200 to 400 ppm for masonry pools and spas, 80 to 200 ppm for vinyl or fiberglass. Never above 2,500 ppm. |
| Pool Water Treatment Advisory Group (UK) | Ideally 80 to 200 mg/l as calcium carbonate; above 300 mg/l scale can form with sudden changes in temperature and pH. |
| SA Health, South Australia (home pools) | 150 to 400 mg/L |
The ranges are not the same: the CDC itself sets a lower one for vinyl and fiberglass than for masonry, because low calcium attacks plaster. Your pool builder or the liner maker may give a figure for your pool.
Raising it with calcium chloride
Calcium chloride is what calcium hardness increasers are made of: the safety data sheet of Pool Time's increaser, for example, lists 75 to 97 percent calcium chloride. Each molecule adds one calcium, which the test counts as one molecule of calcium carbonate. With PubChem's molar masses, raising 10,000 gallons by 10 ppm takes 378.5 grams counted as calcium carbonate, which is 0.925 pounds of pure calcium chloride. Products are not pure: ordinary flakes are 77 to 80 percent, so the same job takes about 1.20 pounds of them. OxyChem rounds this to one pound of its 83 to 87 percent flakes.
Add it the way the label says, with the pump running. HTH's label sets a limit of 10 pounds per 10,000 gallons at one time and, for increases of more than 50 ppm, a third of the dose at a time, 4 to 6 hours apart. Calcium chloride gives off a lot of heat as it dissolves.
Lowering it
No chemical takes calcium out of a pool. NSW Health's guidelines say to replace part of the pool water with make-up water that has less calcium. The share to replace is (hardness now − target) ÷ (hardness now − fill water hardness), so the fill water must be softer than the target. Where the tap water itself is hard, the CDC notes that lowering the hardness is not always possible, and the UK guidance asks that treatment chemicals at least not add more.
Questions people ask
What should the calcium hardness be in a pool?
The CDC prefers 200 to 400 ppm for public pools, 80 to 200 for vinyl or fiberglass when balancing the water, and the UK's pool guidance 80 to 200. South Australia's health department gives 150 to 400 for home pools.
How much calcium chloride raises hardness by 10 ppm?
In 10,000 gallons, 0.925 pounds of pure calcium chloride, or about 1.20 pounds of ordinary 77 percent flakes.
How do you lower calcium hardness in a pool?
By draining part of the water and refilling with softer water. The share to replace is the drop you need divided by how much harder the pool is than the fill water.
Is calcium hardness increaser just calcium chloride?
Usually, yes. Check the label or safety data sheet for the percentage, and use it in the calculator.
Sources
- CDC Model Aquatic Health Code, 2024 (5th edition): Code — 5.7.4.4.3, maximum calcium hardness
- CDC Model Aquatic Health Code, 2024 (5th edition): Annex — 5.7.4.4.3 and 5.7.4.6, preferred ranges and effects
- Pool Water Treatment Advisory Group (UK): Code of Practice — section 9.10, calcium hardness
- SA Health: Pools at home and maintaining them — ideal range for home pools
- NSW Health: Guidelines for Managing Water Quality in Public Swimming Pools and Spa Pools — raising and lowering calcium hardness
- USGS Water Science School: Hardness of Water — hardness expressed as calcium carbonate
- PubChem: calcium carbonate (CID 10112) and calcium chloride (CID 5284359) — molar masses 100.09 and 110.98 g/mol
- NIST Guide to the SI (SP 811), Appendix B.8 — US gallon 3.785412 liters
- OxyChem: Calcium chloride for pool and spa — dose per 10 ppm and product strengths
- OxyChem: DOWFLAKE Xtra 83-87% product information sheet — conventional flake 77-80 percent
- HTH Pool Care: Calcium Up — dose limits per addition
- Pool Time Calcium Hardness Increaser: safety data sheet — 75 to 97 percent calcium chloride; heat when dissolving