Plumbing & Water · Calculator
Plumbing Vent Size Calculator
Pick the kind of vent, then enter the drain or stack it serves and how long the vent runs to the open air. The calculator applies the sizing rules of the 2021 International Plumbing Code and shows which rule set the answer.
Minimum vent size
1-1/2 in.
- Half of a 3 in drain
- 1.5 in
- Rule of Section 906.2
- at least half the drain
- Developed length
- 20 ft
IPC 2021 Section 906.2. A planning check, not a stamped design.
A plumbing vent is sized from the drain it protects, not from the trap. A 3 in stack carrying 21 drainage fixture units with a 60 ft vent run needs a 2 in vent under IPC Table 906.1, because the smaller size is only allowed up to 32 ft.
Two rules, depending on the vent
The IPC sizes vents in two different ways.
- Individual, branch, circuit and relief vents (Section 906.2) must be at least half the required diameter of the drain they serve, and never smaller than 1-1/4 inches. A vent longer than 40 feet goes up one nominal size for its whole length.
- Stack vents and vent stacks (Section 906.1) are read from Table 906.1, using the size of the stack, the drainage fixture units it carries and the developed length of the vent. Here too the vent may not be smaller than half the drain it serves or smaller than 1-1/4 inches.
Most vents in a house are individual or branch vents. A stack vent is the upward continuation of a soil or waste stack through the roof; a vent stack runs alongside a drainage stack, and the code requires one for every drainage stack with five branch intervals or more (Section 904.2).
Size the vent from the drain, not the trap
The vent size follows the drain that continues downstream from where the vent connects, and that drain is sized from its drainage fixture units with Table 710.1(2). So a 4 inch drain needs at least a 2 inch vent, a 3 inch drain a 1-1/2 inch vent, and anything from 2 inches down needs the 1-1/4 inch minimum.
When half of the drain is not a standard pipe size, as with a 2-1/2 inch drain, the calculator rounds up to the next nominal size, here 1-1/4 inches. The code does not say how to round, so we chose the reading that never gives a smaller vent.
A worked example
A 3 inch soil stack carries 21 drainage fixture units, and its vent runs 60 feet to the roof. In Table 906.1, the row for a 3 inch stack up to 21 fixture units allows a 1-1/2 inch vent for only 32 feet, so it is too short. The next size, 2 inches, is allowed up to 110 feet, which covers the run. The rule that the vent be at least half the stack, 1-1/2 inches here, is met as well.
Measuring the developed length
For Table 906.1, the developed length is measured along the pipe from the point where the vent connects to the open air. Count every horizontal and vertical piece, not the straight-line distance. For a load between two rows of the table for the same stack size, the calculator uses the next higher row, which never allows a longer vent than the table does.
If no size in the row reaches your length, or the load is above the last row for that stack, the calculator says so. That usually means the stack itself, not only the vent, is too small for the job.
Questions people ask
What size vent does a toilet need?
It depends on the drain the toilet discharges into, not on the toilet. If that drain is 3 inches, an individual vent may be 1-1/2 inches, as long as it is no longer than 40 feet; beyond that it goes up to 2 inches.
Can a vent be smaller than 1-1/4 inches?
No. Under Sections 906.1 and 906.2, no vent may be smaller than 1-1/4 inches, whatever the drain it serves.
Why does a long vent need a bigger pipe?
Air moving through a long, narrow vent loses pressure, and the vent's job is to keep the pressure in the drain close to the outside air so trap seals are not pulled out. That is why Section 906.2 adds one pipe size beyond 40 feet, and why Table 906.1 lists shorter limits for smaller vents.
Sources
- ICC: Methods of Venting Plumbing Fixtures and Traps in the 2021 IPC — Table 906.1, Section 906.2 and worked examples, published by the code's author
- 2021 Michigan Plumbing Code, sample pages (2021 IPC) — text of Sections 906.1 and 906.2