Roof & Exterior · Calculator
Gutter Calculator
Enter the length of each run of gutter. The calculator adds them up, works out how much each run has to fall at the pitch your gutter maker asks for, and counts the downspouts, guard pieces and elbows to buy.
Total gutter
110 ft
- Run 1: 42 ft
- 2 downspouts, fall 1.05 in end to end
- Run 2: 42 ft
- 2 downspouts, fall 1.05 in end to end
- Run 3: 26 ft
- 1 downspout, fall 0.65 in end to end
- Downspouts
- 5 (one per 40 ft of gutter)
- Gutter guard pieces
- 28 × 4 ft
- Elbows
- 15 (3 per downspout)
Pitch: 1/4 in per 10 ft, from Amerimax metal gutters (2010 and 2011 instructions) and Amerimax vinyl (2014). With the downspout in the middle of a run, each half slopes toward it, so the fall is about half.
From gutter makers' installation instructions (Amerimax, Ornametals). Add your own allowance for waste and corners.
A gutter job comes down to a few numbers: the total length, the fall toward each downspout and how many downspouts the length needs. Runs of 42, 42 and 26 feet make 110 feet of gutter, which Amerimax's one-per-40-feet rule turns into 5 downspouts.
Measuring the runs
Measure along the fascia, the board the gutter hangs on, one straight run at a time. A simple gable house usually has two runs, one on each long side; a hip roof or an L-shaped house has more. Enter each run on its own, because each one gets its own pitch and its own downspouts.
How much fall a gutter needs
A gutter is hung with a slight slope toward the downspout so water does not sit in it. The makers do not agree on how much:
- Amerimax's instructions for metal gutters (2010 and 2011) and for its 2014 vinyl gutters say to drop the line about 1/4 inch for every 10 feet.
- Its earlier vinyl instructions, from 2008 and 2009, say 1/8 inch for every 10 feet.
- Ornametals' instructions for its EuroGutterUSA half-round gutters say about 1/4 inch per 20 feet.
So the calculator does not pick one for you: choose the figure from the instructions of the gutter you are actually installing. Whichever you use, the fall adds up along the run, so a long run drops noticeably more at the downspout end than a short one.
How many downspouts
Amerimax's vinyl instructions call for one downspout for every 40 feet of gutter, and the calculator applies that rule run by run: a 42 foot run gets two. On a long run, a downspout in the middle with the gutter sloping toward it from both ends halves the fall at each end. Heavy rainfall, a large roof draining into a short gutter or a valley pouring into one spot can call for more downspouts or a bigger size than the rule of thumb gives.
A worked example
A ranch house has two long runs of 42 feet and a short one of 26 feet over the garage: 110 feet of gutter. At 1/4 inch per 10 feet, each long run falls 1.05 inches from end to end. At one downspout per 40 feet, each long run needs 2 and the short one 1, so 5 downspouts. With guards sold in 4 foot pieces, that is 28 pieces, and with 3 elbows per downspout, 15 elbows.
Guards and elbows
Gutter guards come in pieces of a fixed length, so the count is the total length divided by the piece length, rounded up. Each downspout needs elbows: often a pair at the top to bring it from the gutter outlet back to the wall, and one at the bottom to turn the water away from the foundation. Enter the number your layout needs; a downspout that has to jog around a soffit or a window needs more.
Questions people ask
How much slope should a gutter have?
It depends on the maker. Amerimax's metal gutter instructions say about 1/4 inch every 10 feet; its 2008 and 2009 vinyl instructions said 1/8 inch every 10 feet; Ornametals says 1/4 inch every 20 feet for its half-round gutters. Follow the instructions of your gutter.
How many downspouts do I need?
Amerimax's vinyl instructions say one downspout for every 40 feet of gutter. Add more where a large roof area or a valley drains into a short stretch of gutter.
Should I add extra for waste?
Yes. The calculator gives the measured length. Corners, end caps and cuts eat some material, so round each run up to the lengths the gutter is sold in.
Sources
- Amerimax: metal gutter installation instructions (2010) — about 1/4 in of fall every 10 ft
- Amerimax: metal gutter installation instructions D226979 (2011) — 1/4 in every 10 ft
- Amerimax: Contemporary vinyl gutter instructions (2008) — 1/8 in every 10 ft; minimum 1 downspout per 40 ft
- Amerimax: Traditional vinyl gutter instructions (2009) — 1/8 in every 10 ft; 1 downspout per 40 ft
- Amerimax: Contemporary vinyl gutter instructions D227273-01 (2014) — 1/4 in every 10 ft; drop outlets 1 per 40 ft
- Ornametals: EuroGutterUSA installation guide (2010) — about 1/4 in per 20 ft